![]() ![]() The most convenient way is to use a self-adjustable wire stripper such as the IRWIN VISE-GRIP Self Adjusting Wire Stripper (Model 2078300) and Klein Self-Adjusting Wire Stripper & Cutter (Model 11061) we have reviewed in our post. Klein-Kurve 8-20 AWG Wire Stripper/Cutter This Wire Stripper/Cutter features six stripping This Wire Stripper/Cutter features six stripping holes and a shear-cutting knife to handle 8-18 AWG Solid and 10-20 AWG Stranded wire, plus shearing holes for 6-32 and 8-32 bolts. Finally pull the wire cutter away and outer insulation will be removed.īoth of above mentioned ways require some experience. Once inner wires are exposed, you can strip them like any normal wire would be stripped.Īnother way is to use a conventional wire cutter and instead of cutting the wire, you apply pressure on insulation and rotate the wire inside the jaws of the cutter so that a cut is applied over the circular circumference of the wire. One of the common ways is to use a knife or paper cutter to slice the outermost insulation carefully and expose the inner wires. Timely remove the iron chips wound on the plier's body to ensure smooth chip discharge.You can strip a 3 core flex in different ways depending upon the type of tool you are using. If there is a breakage or other aspects of the problem, promptly carry out the corresponding repair. Other strippers leave your hand fatigued trying to use just the right. The rusty area of the knife mouth is cleaned with rust remover, and some lubricant is applied to the place of the rotating shaft to ensure the pliers can be used normally. This becomes more apparent when using a wire strippers all day with smaller strand wire. If you crimp too thick wires with sharp pliers' heads, the pliers will break. ![]() ![]() Goggles should be worn when cutting wires to protect your eyes.ĭo not use light pliers to crimp hard wires. Use the correct angle for shearing, can not knock the plier handle and pliers head, or use the plier's blade to curl the wire. The rubber sleeve on the handle is to increase the comfort of use unless the handle is specifically insulated, these rubber sleeves are not electrically resistant and cannot be used for electrically charged work. Ordinary pliers can not cut piano wire unless specifically have this function. Pliers can not be used on nuts and bolts, using a wrench would be better, and not easily damaged fasteners. JavaScript seems to be disabled in your browser. Lubricate the pliers often, adding some lubricant to the hinge can extend the service life and can ensure the use of labor-saving.ĭo not extend the length of the handle to obtain greater shear force, but should use the larger specifications of the pliers or wire cutters.ĭo not put the pliers in an overheated place, otherwise, it will cause annealing and damage the tool. The store will not work correctly in the case when cookies are disabled. If abused in this way, the pliers will crack and break, and the edges of the pliers will be chipped off. If you want to strip pliers can be used for a long time, in addition to the use of stripping pliers in addition to standard operation, but also need to pay attention to the following matters.ĭo not use light pliers as a hammer or tap the handles of the pliers. Notes on the use of wire stripping pliers Release the tool handle, and remove the cable, the cable metal is then neatly exposed outside, and the rest of the insulation plastic will be intact. Hold the cable stripping tool handle, clamp the cable, and slowly force the cable to slowly peel off the outer skin. Place the prepared cable in the middle of the stripping tool's blade and select the length of the cable to be stripped. When you insert the wire into the correct hole and squeeze the stripper handle together, it will cut through the plastic insulation precisely without damaging the wire.įirst, select the appropriate stripping blade according to the thickness type of the cable. Wire strippers have a series of marked holes that match the specific gauge of wire for that stripper. It is important to choose the correct wire stripping pliers for the gauge of wire you are stripping. Wire strippers come in a variety of shapes and sizes and often have serrated teeth to help strip the wire. ![]() The cutting slots are sized for various sizes of wire, but not for the wire's insulation coating, so when the wire passes through the slot, its insulation is left behind. Now that you know the wire gauge, finding the. Using this right tool speeds up productivity and. This is accomplished using slotted cutting blades located in the jaws of the stripper. The Correct Way of Using a Wire Stripper First, you must know the correct gauge of the wire you wish to strip. Yes, you can use a utility blade or a side cutter, but often this leads to damaging the cable or your fingers. Most wire strippers are capable of many different tasks, but their main purpose is to strip insulation from the ends of wires. A wire stripper is similar to a pair of pliers or scissors. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |